kindyking

In order to standardize our shoe logo, and promote China's footwear products to the international market, to promote the development of China's footwear industry and improvement. State Quality and Technical Supervision in 1998 l afternoon of May 16 announced the adoption of international standards equivalent ISO9407: l99l world's newest shoe "shoe" (GB/T3293.1-l998) national standards. The standard by the China Institute of Light Industry Association footwear drafted by Zhou Jing, Gao trip Qi Xiaoxia writing since l998, l2 January onwards. The standard shoe by the National Standardization Center and responsible for the interpretation of the standard GB3293-82 instead of the original in the shoe section. Where in the circulation of our shoes on the market, according to the standard must always be marked China shoe. Standard Standard specifies the scope of shoe identification method, and discusses the world shoe (Mondopoint) shoe named after the basic characteristics of the system. Indefinite standard applicable to all types of shoes. New "shoe" introduce a national standard. Shoe its meaning indefinite includes shoes boots, slippers, sandals and all other types of footwear. 2. Shoe foot measurement. It can provide services based on the shoes. 3. Foot length of the longest toe end in contact with the vertical line followed by bumps in contact with the horizontal distance between the vertical money, subjects were to erect [weight evenly distributed on both feet.] And the type of dress and shoes to adapt Socks measure 4. Feet around the perimeter of foot. With a soft tape measure with the first and fifth metatarsal phalangeal joints between the first and fifth place [ie] the perimeter of the metatarsophalangeal joint, guillotine amount of soft feet not too loose or too tight. Measurement conditions with the same foot length measurement. 5. Feet wide feet around the horizontal projection. On behalf of the first and fifth metatarsophalangeal joint contact between the two vertical lines horizontal distance measurement conditions with the same foot length measurement. 6. Normal foot and anatomical studies based on statistical results and definitions in the foot. The standard shoe made basic characteristics: shoe based on the International System of Units (SI), measurement of the foot just international system of units. Shoe measurement system based on the following two values: a) foot length (according to the standard definition of three regulations adopted); b) b) feet wide (according to the standard definition of five regulations adopted). Note: The above does not preclude the use of the various stages in the shoe around the foot. The method of determining shoe: Each shoe is based on the corresponding measured values ​​of normal feet OK. Shoe measured value representation: long legs and feet corresponding to the width of the measured values ​​must be expressed in millimeters. Note: This requirement does not preclude use code as a foot wide auxiliary representation. This code could become future international standard Huai topic. Shoe identification method: l. Identification number identifies the elements of shoes should include foot length indication, then (if required) is a foot wide indication. Both values ​​are in millimeters integer (not specify unit), each other to short-term or slash. The font height of at least 3mm, to avoid confusion with other possible should be clearly marked to separate (e.g., a continuous closed line, such as rectangular or oval, etc.). (2) identify the location of a) on a shoe with pairs of each shoe on both the visible and easy to read in the appropriate parts of the marked shoe. b) In fooled shoe shoebox packaging or other packaging, the packaging must be marked on the shoe. 3 identifies the form and in the form of identification methods used (stamping, printing, labeling, etc.) arranged by the manufacturer. Shoes on the logo should be clearly visible within the necessary time and easy reading. The conversion of the existing system of shoe is different from the existing world shoe shoe made of any kind shall prepare the corresponding shoe world, the method of the existing translated into each shoe fit the foot of the corresponding normal Length (with a few millimeters). Each shoe can also include a few millimeters in width code. "Shoe" Standard Annex A (informative) Examples shoe identification method: Al shoe can show the value feet long, a foot wide showing the value of an integer mm, can choose one of the following forms A2 also showing the value of their feet long mm integers and "type" means, but the type code in brackets indicate. For example: Chinese shoe 241/2 II into the world shoe 245 (2); Chinese shoe 26 into two semi-world shoe 260
from shoes manufacturer shoes factory women shoes manufacturer